Precision cold-rolled stainless steel strip, coil and belt solutions

Titanium Grade 2 Precision Slit Strip

Commercially pure Grade 2 titanium strip, precision slit and wound to drawing for specialist industrial applications.

Need a specific grade, temper or slit width? Send the drawing, target tolerance and estimated annual volume. Our team will review the requirement with manufacturing.

Request a technical quote

Titanium Grade 2 Precision Slit Strip is supplied for projects where one dimensional value is not enough: the finished edge must also feed, form, weld, seal or wear predictably. This titanium Grade 2 precision slit strip option combines a reviewed material condition, custom slit width, edge treatment and a winding format matched to the production handle.

HIQ Material coordinates the specification around the finished component, not just the master coil. Share the grade, temper, thickness, finished width, burr direction, edge drawing, coil mass, inside diameter and the first operation on your line. The quotation can then define measurable acceptance points instead of relying on a general “clean edge” description.

Why specify a titanium Grade 2 precision slit strip

The edge is a functional surface. A burr that looks minor on a sample can scratch a coating, jam a guide, puncture a seal or concentrate stress during bending. At the same time, removing too much material can change contact geometry or reduce available section. The right specification balances those effects with the material and the way the strip is handled.

  • Grade 2 titanium offers useful corrosion resistance with good formability in suitable sections.
  • Titanium springback and surface sensitivity call for dedicated knife and tension settings.
  • Edges are protected from cross-contamination and handling marks during winding and packing.
  • Material certificates, condition and inspection requirements should be specified before quotation.

Technical parameters

MaterialASTM Grade 2 commercially pure titanium; Grade 1 and other grades by review
Thickness0.05-1.50 mm, subject to titanium condition and finished width
Finished widthFrom 3 mm; narrower widths reviewed against gauge and edge quality
Width toleranceTypical slit-width tolerance +/-0.05 mm
EdgeDeburred or round edge; sharp square edge only after application review
WindingCoreless, paper core or plastic spool
SurfaceAs-rolled, annealed or pickled condition to project requirement

These are planning ranges, not an automatic release limit. Final feasibility is confirmed against the actual material condition, master-coil width, finished width, edge geometry, coil build and inspection plan. Very thin strip or very narrow width can magnify burr, camber and edge-wave effects, so a sample review is recommended before a production order.

Applications

The titanium Grade 2 precision slit strip is normally specified where repeatable material feed and a controlled edge influence part quality. Typical review cases include:

  • Chemical and desalination equipment
  • Medical and laboratory hardware
  • Corrosion-resistant connectors and fasteners
  • Lightweight industrial and aerospace prototypes

Edge and quality control

Inspection should match the failure mode. For a sharp-edge risk, measure burr height and record which face carries the burr. For a radius or chamfer, check profile and orientation rather than width alone. For automated feed, inspect edge wave, crossbow, layer alignment and the position of the strip in the pack. Surface appearance may require protection film or interleaving even when dimensional results are correct.

An effective inspection plan can include incoming material review, slit-width measurement, visual edge classification, burr-height sampling, flatness checks and packaging verification. If the component is welded, formed, coated or heat treated, include a short downstream trial in the approval. This connects the coil specification to the process condition that actually matters.

How to request a quotation

  • State the exact material grade and required temper or mechanical condition.
  • Provide nominal thickness, finished width and the measuring method behind each tolerance.
  • Attach an edge sketch or photo and identify the burr side and edge orientation.
  • Specify coil or spool mass, inside diameter, outside-diameter limit and winding direction.
  • Describe the first downstream operation, expected annual quantity and required documentation.

Related specifications and technical guidance: Titanium Strip Category · High-Strength Stainless Strip Guide · Stainless Steel Slitting Burr Guide.

For an edge or metallurgical check, use the relevant ASTM International or ISO standard named in your drawing. Do not use a generic catalogue limit as a substitute for the product standard.

Frequently asked questions

Can the titanium Grade 2 precision slit strip be supplied as a sample?

Yes, a trial section or short coil can be reviewed when material and processing setup are available. Approve the edge direction, burr limit, width method and winding format before scaling to production.

Which edge should be specified for automated feeding?

A deburred or round edge often reduces snagging, but the best choice depends on guide material, strip thickness, tension and the way the strip enters the tool. A square edge may remain necessary for contact geometry.

Can slit width and edge treatment be combined?

Yes. The edge allowance, finished width and winding stability are reviewed together. Tightening one tolerance can change the practical minimum width or the suitable package format.

How should packaging be selected?

Choose paper core, plastic spool or coreless winding after considering the dereeler, coil mass, available floor space, shipping method and risk of edge damage. Protective film or rust-inhibiting paper can be added when the application requires it.

Send your drawing and edge requirement to HIQ Material